A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
What are your insights and beliefs on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is readily available, the job can relocate easily; if you need to open up a wall surface to remove the old tub and position the new tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task and also fit trying it. Rather than hiring a professional to take control of a halfway-completed job, it is far better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your shower room if you have actually currently gotten a brand-new bathtub as well as do not require to alter the setup of your previous water system pipelines.
Your devices as well as material checklist must make up the following:
Preparing for the Installation
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to stop pressure on the tub.
Fit the versatile tap adapters to the bottom of both faucets using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing faucets can be quite bothersome due to the limited access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the tub in the called for position. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the bath tub till the spirit level reads level.
To set up faucets, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Switch on the water system and also examine all joints and new pipework for leaks as well as tighten them if needed. Load the bath tub as well as also check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, deal with the bath paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait up until the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in area in between the faucet and the sink. Secure the tap in position with the manufacturer provided backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type should be connected to the faucet finishes initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to crack an inflexible seal, creating the water to pass through the wall in between the bathroom as well as the tiling, causing problems with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components and fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that piece of writing about Tools You Need to Install a New Bathtub while exploring the internet. Do you know about another individual who is excited by the subject? Take a moment to share it. Thanks for your time. Come back soon.
Get Estimate
Report this page